ръководство на потребителя PHILIPS 33281-60-16

[. . . ] Never connect the product to the power outlet if the voltage is different. Risk of injury or damage to the SoundBar!• For wall-mountable products, use only the supplied wall mount bracket. Secure the wall mount to a wall that can support the combined weight of the product and the 3 EN • wall mount. [. . . ] • The product/remote control may contain a coin/button type battery, which can be swallowed. Keep the battery out of reach of children at all times!If swallowed, the battery can cause serious injury or death. Severe internal burns can occur within two hours of ingestion. • If you suspect that a battery has been swallowed or placed inside any part of the body, seek immediate medical attention. • When you change the batteries, always keep all new and used batteries out of • reach of children. Ensure that the battery compartment is completely secure after you replace the battery. If the battery compartment cannot be completely secured, discontinue use of the product. Keep out of reach of children and contact the manufacturer. Care of the environment Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. This is CLASS II apparatus with double insulation, and no protective earth provided. Mains fuse This information applies only to products with a UK mains plug. This product is fitted with an approved molded plug. If you replace the fuse, use one with: • the ratings shown on the plug, • a BS 1362 approval, and • the ASTA approval mark. h VOLUME +/Increase or decrease volume. i AUDIO-IN Switch your audio source to audio input connection (3. 5mm jack). j AUX Switch your audio source to the AUX connection. a d b c Connectors This section includes an overview of the connectors available on your SoundBar. a AUDIO IN-AUX Connect to an analog audio output on the TV or an analog device. b DIGITAL IN-COAXIAL Connect to a coaxial audio output on the TV or a digital device. c DIGITAL IN-OPTICAL Connect to an optical audio output on the TV or a digital device. d AC MAINS~ Connect to the power supply. Side right a a AUDIO-IN Audio input from an MP3 player (3. 5mm jack). 7 EN 3 Connect This section helps you connect your SoundBar to a TV and other devices. For information about the basic connections of your SoundBar and accessories, see the quick start guide. Note •• For identification and supply ratings, refer to the type •• Before you make or change any connections, make sure plate at the back or bottom of the product. that all devices are disconnected from the power outlet. Option 2: Connect audio through a digital coaxial cable Best quality audio 1 Connect audio from TV and other devices Play audio from TV or other devices through your Soundbar speakers. Use the best quality connection available on your TV, Soundbar, and other devices. Using a coaxial cable, connect the COAXIAL connector on your SoundBar to the COAXIAL/DIGITAL OUT connector on the TV or other device. • The digital coaxial connector might be labeled DIGITAL AUDIO OUT. Option 3: Connect audio through analog audio cables Basic quality audio Option 1: Connect audio through a digital optical cable Best quality audio 1 Using an analog cable, connect the AUX connectors on your SoundBar to the AUDIO OUT connectors on the TV or other device. DVD TV 1 Using an optical cable, connect the OPTICAL connector on your SoundBar to the OPTICAL OUT connector on the TV or other device. • The digital optical connector might be labeled SPDIF or SPDIF OUT. EN 8 4 Use your SoundBar This section helps you use the SoundBar to play audio from connected devices. [. . . ] bears no responsibility for improper wall mounting that results in accident, injury or damage. If you have any query, contact Philips Consumer Care in your country. •• Before wall mounting, make sure the wall can support the weight of your SoundBar. Screw length/diameter Depending on the type of wall mounting your SoundBar, make sure that you use screws of a suitable length and diameter. 3 - 3. 5mm > 25mm For information about how to wall mount your SoundBar, see the quick start guide. EN 10 6 Product specifications Note •• Specifications and design are subject to change without notice. Amplifier • • • • Total output power: 40W RMS (+/- 0. 5 dB, 10% THD) Frequency response: 20 Hz-20 kHz / ±3 dB Signal-to-noise ratio: > 65 dB (CCIR) / (A-weighted) Input sensitivity: • AUX: 650 mV • AUDIO-IN: 400 mV Audio • S/PDIF Digital audio input: • Coaxial: IEC 60958-3 • Optical: TOSLINK Main unit •• •• •• • • •• •• Power supply: 220-240 V~, 50 Hz Power consumption: 40 W Standby power consumption: ≤ 0. 5 W Speaker impedance: 8 ohm (full range) Speaker drivers: 4 x 54. 5 mm (2") Dimensions (WxHxD): 845 x 74. 5 x 94 mm Weight: 2. 0 kg Remote control batteries • 1 x CR2025 11 EN 7 Troubleshooting Warning •• Risk of electric shock. Never remove the casing of the product. To keep the warranty valid, never try to repair the product yourself. [. . . ]